RENAULT - 5 2nd Generation - Lexan Polycarbonate right front door window

Budget Slider Kit

Our budget Lexan Polycarbonate window slider kit is used in many forms of motorsport.

Built using our custom injection-moulded design to ensure minimal contact between the slider and the window.

Designed to prevent the slider panel rubbing on the window and scratching it.

• Injection moulded polycarbonate rails.
• Injection Moulded Polycarbonate handles.
• All stainless steel (INOX) fixings supplied.

Clubman Slider Kit

Mid-range Slider kit suitable for all rally / race applications.

Sprung ball bearing system in the handle secures the window into position and stops it sliding back and forth under braking and acceleration.

• Injection moulded polycarbonate rails.
• Injection Moulded Polycarbonate handles.
• All stainless steel (INOX) fixings supplied.
• Clubman Spec Bearing lock system.

Pro Slider Kit

Our Pro slider kit is used in many forms of motorsport. The fully vacuum formed enclosure helps to resist water and dirt from entering the car.

The sprung ball bearing system in the handle secures the slider panel into position and stops it sliding back and forth under accelleration and braking.

• Vacuum formed full frame enclosure.
• Injection Moulded Polycarbonate Handle.
• Bearing Lock system to stop unwanted movement of the panel.

WRC Slider Kit

Flush fitting WRC / R5 Lightweight polycarbonate window slider kit as used in WRC & R5 rally cars.

Purely designed for harsh motorsport applications and thoroughly tested in the WRC.

• Ultralight Injection moulded polycarbonate slider rails & Handle.
• Stainless steel retaining springs.
• Stainless steel fixings.
• Flush fitting when closed for maximum aerodynamics.

WHICH THICKNESS SHOULD I CHOOSE?

3mm - our lightest and most flexible choice. It is a good choice for when you are bonding or bolting windows into the car like the rear screen and rear quarter windows, or if you are going to permanently fix the door windows into the doors. 

4mm - the best all-round thickness choice. 4mm gives you good weight savings and also remains fairly rigid so you can use it for any bonded or bolted in windows or windows fitted into rubber seals as well as the majority of door windows.

5mm - thick and heavy duty windows. We usually would use 5mm on frameless door windows or for some vintage race cars with big curved rear screens.

More information can be found here.

ARE your windows curved and PRE-CUT TO FIT?

Yes, all of our windows are trimmed to the size of the stock windows. However, there are a few exceptions where we deliberately make the windows a little bigger in order to fit where body trims are bonded to the glass, but we can not add them to the polycarbonate.

All of our windows are also pre-curved to the curvature of the original glass. 

Can I use the original window mechanism?

Yes, as all of our windows are direct OEM window replacements, you can wind our windows up and down. We highly recommend you choose our hardcoating option if you intend to use the original winder mechanism, otherwise your window will scratch with immediate use. Please also ensure any rubber seals are free of grit/ debris or these will also scratch your windows.

Do your windows come with black borders?

Yes, if your OEM windows came with black borders from factory then your polycarbonate windows will come with black borders pre-applied. We will even add a dot matrix if the original glass had one.

How do I fit my Lexan Polycarbonate windows?

We have written guidelines for fitting your windows, which you can find here.

Do not be tempted to use any glues or primers that are designed to bond glass windows into cars. These primers and cleaners are too aggressive for polycarbonate, and the typical glass adhesive does not allow for expansion in the polycarbonate. These will damage your windows.

Are your windows FIA/ MSA approved?

The FIA/ MSA or other regulatory bodies do not actually ‘approve’ any manufacturers' windows. The FIA / MSA publish a set of requirements that windows must be made to, and this usually involves using a recognised shatterproof material of a certain thickness and permanently marked to indicate this.

All of our Polycarbonate products meet all the current material specifications for construction from a shatterproof plastic, and we can provide thickness’s to suit the required regulations. Our windows are permanently marked with the appropriate material specifications and ID numbers required.